Sort Most relevant
Showing 36 of 6881 results
-
Quick and easy disposable mini paint tray liner to suit UNi-PRO 100mm mini roller tray. Created to fit perfectly into the contoured design of the UNi-PRO mini roller tray. No need to clean up after painting, simply wipe out excess paint and lift out.Handy Tip:To help make cleaning quicker and easier use a disposable tray liner. This allows you to keep your original tray and just replace the liner after each coat.
-
- Ideal for rigging purposes
- Assorted Colours
- Spring loaded gate
-
- A plug to seal the end of 13mm poly tube
- Use Locking Clamp or Loc-Sure Clamp to secure fitting
- UV stabilised
-
- Suits patio style irrigation
- Beige coloured poly fitting
- Micro FItting
-
- Assorted colours
- Ideal for bulletin boards
- Pack of 50
-
- Customisable — Designed to be cut and bent to fit your specific bracket needs
- Perforations — Featuring round holes for secure screws and diamond holes for ease of cutting and bending
- Easy Installation — Simply mark your desired location and securely attach your customised bracket
- 1mm Galvanised Steel — Effortlessly bends by hand for quick adjustments
-
- Taps into mainline of water supply
- 90 Degree take-off angle
- Connect drip line at angle
- 13mm x 10mm barbed ends
-
- Recommended by Teflon® for use on non-stick coatings on the market
- Removes difficult dirt, without scratching
- The thin scouring layer is flexible and easy to clean utensils of different shapes and sizes
-
- Low profile Cup Head gives a flush finish
- Square neck feature limits bolt spinning during application and provides a smooth secured finish
- Coarse thread allows for maximum grip strength in applications
- Hexagonal nuts included
- Made to Australian Standards BOLT: AS 1390, NUT: AS 1112
-
- Hexagonal head allows for increased clamping pressure
- Coarse thread allows for maximum grip strength in applications
- Hexagonal Nuts included
- Made to Australian Standards BOLT: AS 1111, NUT: AS 1112
-
- Low profile Cup Head gives a flush finish
- Square neck feature limits bolt spinning during application and provides a smooth secured finish
- Coarse thread allows for maximum grip strength in applications
- Hexagonal nuts included
- Made to Australian Standards BOLT: AS 1390, NUT: AS 1112
-
- Pre-punched nails
- Suitable for all timbers, from the lightest softwoods to the densest hardwoods
- Designed for fast construction jointing of timber frames using a hammer
-
- Patented "pull-down" expansion sleeve closes gaps of up to 5mm providing enhanced security.
- Fully assembled "through fixture" anchor eliminates marking out and re-positioning of fixtures.
- Features unique "pull-down" section
-
- Constructed from durable metal
- Easily removes paint can lids
- Can also be used as a bottle opener
-
- Customisable — Designed to be cut and bent to fit your specific bracket needs
- Perforations — Featuring round holes for secure screws and diamond holes for ease of cutting and bending
- Easy Installation — Simply mark your desired location and securely attach your customised bracket
- 2mm Galvanised Steel — Easily bendable with a vice for precise customisation
-
- Use for many nail fixed timber joints
- Made from Galvabond® sheet steel for high resistance to corrosion
- Satisfies the minimum specification of clause 1.15 of AS1684 part 2 and 3, and clause 1.14 of AS1684.4
-
- Use for many nail fixed timber joints
- Made from Galvabond® sheet steel for high resistance to corrosion
- Satisfies the minimum specification of clause 1.15 of AS1684 part 2 and 3, and clause 1.14 of AS1684.4
-
- Built in slots allow for vertical movement in the truss over time without transferring load to the wall
- Made from Galvabond sheet steel for high resistance to corrosion
- Stabilising the tops of internal walls
-
- Pryda Multigrips suitable for high load applications such as a tie-down connector for trusses or rafters to top plates for fixing joists to the face of bearers
- Manufactured from G300-Z275 galvanised steel or marine grade stainless steel.
- Trusted Pryda quality
-
- Negative rake teeth for firm grip
- Suits 25mm poly tubing
- UV stabilised material
- Single unit
-
- Patented "pull-down" expansion sleeve closes gaps of up to 5mm providing enhanced security
- Fully assembled "through fixture" anchor eliminates marking out and re-positioning of fixtures
- Features unique "pull-down" section
-
- Foil fix can be used to fix foil insulation to both wall and roof frames.
- Twisted nail profile allows ready penetration into and excellent holding power in all timbers, from the softest to the hardest.
- Rounded and coined edges, and a wide size (21mm), greatly reduce the tendency of foil insulation to tear in windy conditions.
- Supplied in easy snap-off sticks of 10 for fast, convenient and safe use on-site.
- Made from Galvabond® sheet steel for high resistance to corrosion.
-
- For joining timber at right angles
- Roof batten or purlin to a truss or rafter
- Made from Galvabond® sheet steel for high resistance to corrosion
-
- Restricts water flow
- Secure with 13mm locking clamps
- UV stabilised
-
- Patented "pull-down" expansion sleeve closes gaps of up to 5mm providing enhanced security
- Fully assembled "through fixture" anchor eliminates marking out and re-positioning of fixtures
- Features unique "pull-down" section
-
- Pre-punched nails
- Suitable for all timbers, from the lightest softwoods to the densest hardwoods
- Designed for fast construction jointing of timber frames using a hammer
-
- For joining timber at right angles
- Made from Galvabond® sheet steel for high resistance to corrosion
- Usage: roof batten or purlin to a truss or rafter; tie-down connectors; carport construction; deck construction; right angle joints; pergola construction
-
- Use as a tie-down connector or right angle joint for construction of carports, decks or pergolas
- Made from Galvabond® sheet steel for high resistance to corrosion
- Suitable for lighter load applications
-
- Galvanised making it suitable for outdoor and indoor use
- Distributes the load of the threaded fastener and nut!
- Metric sizing
-
- Use as a tie-down connector or right angle joint for construction of carports, decks or pergolas
- Made from Galvabond® sheet steel for high resistance to corrosion
- Satisfies the minimum specification of clause 1.15 of AS1684 part 2 and 3, and clause 1.14 of AS1684.4.
-
- Suitable for sealing water pipe threads
- WaterMark approved to WMTS-014:2016 - Licence No. WM-032297
- Working temperature: -100℃ - 250℃
-
- Used for the joining of 13mm poly tube or Drip Eze
- Used to extend or repair a watering system
- UV Stabilised
- Secure with Locking Clamps or Loc-Sure Clamps
-
- Negative rake teeth for firm grip
- Suits 13mm poly tubing
- UV stabilised material
-
- Hexagonal head allows for increased clamping pressure
- Coarse thread allows for maximum grip strength in applications
- Hexagonal Nuts included
- Made to Australian Standards BOLT: AS 1111, NUT: AS 1112
-
- Mounting holes for easy installation
- Keeps the irrigation tube neat and tidy
- UV Stabilised
-
- Ideal for connecting timber
- Made from Galvabond® sheet steel for high resistance to corrosion
- Fixing battens or purlins to trusses or rafters
