Chemical Anchors
Sort Best selling
Showing 36 of 37 results
-
- Suitable for cleaning holes 8mm to 12mm in diameter up to 280mm deep
- Clean dust and debris from holes
- Easy to use
-
- Anti-rotation barbs prevent the anchor from rotating in the hole
- Countersunk sleeve allows for flush finishing
- Nylon sleeve reduces the effects of cold bridging i.e mould growth, when compared to all-metal anchors
- Suitable for use with 14 - 18 gauge screws
-
- Spreads adhesive 360 degrees
- Utilised in close to edge applications
- Accommodates 8 and 10mm Ramset Anchor Studs
-
- Hammer-in method makes installation quick and easy
- Full expansion of the anchor is evident when the head of the expansion nail sits flush with the flange
- Once fully set, the ShureDrive™ becomes tamper resistant
- Large flange prevents pull-out
-
- Anti-rotation barbs prevent the anchor from rotating in the hole
- Countersunk sleeve allows for flush finishing
- Nylon sleeve reduces the effects of cold bridging i.e mould growth, when compared to all-metal anchors
- Complete with countersunk screw for a flush finish
-
- Anti-rotation barbs prevent the anchor from rotating in the hole
- Countersunk sleeve allows for flush finishing
- Nylon sleeve reduces the effects of cold bridging. e.g. mould growth, when compared to all-metal anchors
- Complete with hex head screw for a easy installation
- Supplied with galvanised screw for increased corrosion protection in external applications
-
- Anti-rotation barbs prevent the anchor from rotating in the hole
- Countersunk sleeve allows for flush finishing
- Nylon sleeve reduces the effects of cold bridging. e.g. mould growth, when compared to all-metal anchors
- Complete with hex head screw for a easy installation
-
- Anti-rotation barbs prevent the anchor from rotating in the hole.
- Countersunk sleeve allows for flush finishing.
- Nylon sleeve reduces the effects of cold bridging. e.g. mould growth, when compared to all-metal anchors.
- Complete with countersunk screw for a flush finish.
-
- Anti-rotation barbs prevent the anchor from rotating in the hole
- Countersunk sleeve allows for flush finishing
- Nylon sleeve reduces the effects of cold bridging i.e mould growth, when compared to all-metal anchors
- Complete with hex head screw for a easy installation
-
- Cut to length as required.
- Light duty anchoring in concrete, stone, solid brick and solid block
- For use with 3 - 3.5mm nails or 4.5 - 6 gauge screws
-
- Anti-rotation barbs prevent the anchor from rotating in the hole.
- Countersunk sleeve allows for flush finishing.
- Nylon sleeve reduces the effects of cold bridging. e.g. mould growth, when compared to all-metal anchors.
- Complete with hex head screw for a easy installation.
-
- Tapered at one end for quick and easy insertion
- Economical roll
- Suitable for 4.5 - 6 gauge screws
-
RAMSETRamset Hole Cleaning Pump
- Suitable for blowing dust from drilled holes.
- cleaning dust and debris from holes
- Easy to use
-
- Tapered at one end for quick and easy insertion.
- Economical roll.
- Suitable for 10 - 12 gauge screws.
-
- Can be used in hollow or solid applications
- Have a hex head for easy driving into the chemical
- Minimum embedment lines for maximum results
- Galvanised for corrosion protection
-
- Tapered at one end for quick and easy insertion
- Economical roll
- Suitable for 8 - 9 gauge screws
-
- Tapered at one end for quick and easy insertion
- Economical roll
- Suitable for 14 - 16 gauge screws
-
- Anti-rotation barbs prevent the anchor from rotating in the hole
- Countersunk sleeve allows for flush finishing
- Nylon sleeve reduces the effects of cold bridging i.e mould growth, when compared to all-metal anchors
- Complete with hex head screw for a easy installation
- Supplied with galvanised screw for increased corrosion protection in external applications
-
- Anti-rotation barbs prevent the anchor from rotating in the hole
- Countersunk sleeve allows for flush finishing
- Nylon sleeve reduces the effects of cold bridging i.e mould growth, when compared to all-metal anchors
- Complete with countersunk screw for a flush finish
-
- Anti-rotation barbs prevent the anchor from rotating in the hole
- Countersunk sleeve allows for flush finishing
- Nylon sleeve reduces the effects of cold bridging i.e mould growth, when compared to all-metal anchors
- Complete with hex head screw for a easy installation
-
- Anti-rotation barbs prevent the anchor from rotating in the hole
- Countersunk sleeve allows for flush finishing
- Nylon sleeve reduces the effects of cold bridging i.e mould growth, when compared to all-metal anchors
- Complete with hex head screw for a easy installation
- Supplied with galvanised screw for increased corrosion protection in external applications
-
- Can be used in hollow or solid applications
- Hex head for easy driving into the chemical
- Minimum embedment lines for maximum results
- Galvanised for corrosion protection
-
- Anti-rotation barbs prevent the anchor from rotating in the hole
- Countersunk sleeve allows for flush finishing
- Nylon sleeve reduces the effects of cold bridging i.e mould growth, when compared to all-metal anchors
- Complete with hex head screw for a easy installation
-
- Cut to length as required
- 50 metre roll
- Easy to use
-
- Suitable for use with Ramset™ powder actuated tools.
- For fastening to standard strength concrete, masonry and steel up to a maximum of 8mm.
- 1200N/mm2 Shear Strength.
- 1950N/mm2 Shear Strength.
- 52-55HRC Hardness.
-
- Suitable for use with Ramset™ powder actuated tools.
- For fastening to standard strength concrete, masonry and steel up to a maximum of 8mm.
- 1200N/mm2 Shear Strength.
- 1950N/mm2 Shear Strength.
- 52-55HRC Hardness.
-
- High performance Grade 5.8 carbon steel, pre-cut to standard chemical anchoring lengths and supplied with nuts and washers
- Gold passivated, zinc plated for indoor or dry climates
- Depth set mark to ensure correct embedment
- Reliable external hex drive for installing with capsules.
- Chisel-ended to prevent unthreading.
-
- Suitable for use with the FrameBoss™ Powder Actuated Tool magazine.
- For fastening to standard strength concrete, masonry and steel up to a maximum of 8mm.
- 1120N/mm2 Shear Strength.
- 50-55HRC Hardness.
-
- Available with pre-assembled washers to improve pullover strength.
- Manufactured from high-strength material to avoid breakage.
- Available with either a plain or striated shank, and in a range of different sizes and head styles
-
- Anti-rotation barbs prevent the anchor from rotating in the hole
- Countersunk sleeve allows for flush finishing
- Nylon sleeve reduces the effects of cold bridging, such as mould growth, when compared to all-metal anchors
- Complete with hex head screw for a easy installation
-
- Ideal for contact with drinking water
- Ideal for machinery hold down, hand rail and balustrade posts and water treatment plants
- Seismic C1 & C2 performance data
-
- Can be used in hollow or solid applications
- Hex head for easy driving into the chemical
- Minimum embedment lines for maximum results
- Galvanised for corrosion protection
-
- Suitable to anchor into stone, concrete, solid brick, hollow wall and hollow brick
- Strong holding power, up to 32kg into solid substrate and up to 11kg into hollow wall
- Trusted Ramset quality
-
- Suitable to anchor into stone, concrete, solid brick, hollow wall and hollow brick
- Strong holding power, up to 26kg into solid substrate and up to 7kg into hollow wall
- Trusted Ramset quality
-
- Suitable to anchor into stone, concrete, solid brick, hollow wall and hollow brick
- Strong holding power, up to 32kg into solid substrate and up to 11kg into hollow wall
- Trusted Ramset quality
-
- Light duty fixing into brick, concrete or plasterboard
- Box of 40
- Supports up to 26kg in concrete and 7kg in plasterboard
