Fasteners & Fixings
Sort Best selling
Showing 36 of 2449 results
-
- Superior vibration resistance and clamping force
- Ideal for most sheet metal fabrications
- Excellent tolerance to corrosion
- 316 Grade stainless steel body and mandrel
-
- Spreads adhesive 360 degrees
- Utilised in close to edge applications
- Accommodates 8 and 10mm Ramset Anchor Studs
-
- External star washers
- External tabs are located on the outer diameter, providing superior locking capabilities
- Ideal for applications that require continuous reliability
- Zinc plated for internal applications
- Assortment pack of M14, M15, M16
-
- M4 metric thread size x 25mm length
- Hex head
- Zinc plated
- Pack of 8
- Thread pitch: 0.7mm
-
- Imperial sizing
- Round head for raised finish
- Zinc Plated suitable for internal use and areas not subject to direct weather
-
- 8.5mm hole size x 16mm overall diameter
- Matte black finish
- Pack of 12
-
- M5 metric thread size x 75mm length
- Round head
- Zinc plated
- Pack of 4
- Thread pitch: 0.8mm
-
ZENITHZenith 6G x 20mm Florentine Bronze Hinge-Long Threads Countersunk Head Timber Screws - 40 Pack
- Countersunk Head for flush finish
- No ribs for flush finish through metal e.g. Hinges
- Suitable for attaching hinges and general timber applications
-
- Anti-rotation barbs prevent the anchor from rotating in the hole.
- Nylon sleeve reduces the effects of cold bridging. e.g. mould growth, when compared to all-metal anchors.
- Suitable for use with 14 - 18 gauge screws.
-
- M3 metric thread size x 35mm length
- Round head
- Zinc plated
- Pack of 8
- Thread pitch: 0.5mm
-
- Low profile head allows for low profile fixing.
- Large flange prevents the head from pulling into the substrate.
- Anti-rotation barbs, incorporated in the flange, prevent the anchor from spinning in the hole.
- Collapsing legs with an integral nut provide high strength and allow the screw to be removed without loosing the anchor inside the cavity.
-
- M3 metric thread size x 25mm length
- Hex head
- Stainless steel 316
- Pack of 12
- Thread pitch: 0.5mm
-
- M3 metric thread size x 15mm length
- Round head
- Zinc plated
- Pack of 20
- Thread pitch: 0.5mm
-
- Nylon is lightweight, tough, resistant to corrosion, and has good electrical insulating properties
- Conform easily to irregular surfaces and provide limited vibration dampening
- Suitable for imperial and metric
- For external use
-
- Two large metal 'wings', one on each side, for easy tightening and removal by hand without tools
- For Whitworth threaded bolts
- Manual fixing
-
- For internal use
- Perfect for soft materials like plastic, wood, leather etc
- Chrome plated finish
-
- Patented "pull-down" expansion sleeve closes gaps of up to 5mm providing enhanced security.
- Fully assembled "through fixture" anchor eliminates marking out and re-positioning of fixtures.
- Countersunk head provides a neat finish, flush with the fixture surface
-
- M6 metric thread size x 40mm length
- Hex head
- Zinc plated
- Pack of 6
- Thread pitch: 1mm
-
- 5mm Tungsten Carbide Drill
- 10 x 35mm White Wall Plugs
- 10 x 35mm 4G Screws
-
- Superior corrosion protection
- 6 Pack
- Thread pitch: 0.7mm
-
- Strong vibration resistance and clamping force
- Lightweight and easy to set
- Good corrosion resistance
- Cost effective
-
- Round head
- Stainless steel 304
- Pack of 8
- Includes Torx® driver bit
- Thread pitch: 1mm
-
- Rubber washers are both durable and resistant to fluids
- Suitable for imperial and metric
- For external use
-
- M6 metric thread size x 20mm length
- Hex head
- Zinc plated
- Pack of 8
- Thread pitch: 1mm
-
- High tensile
- Yellow zinc
- 10 pack
- Thread pitch: 1mm
-
- Countersunk head for flush finish in hinges
- Self-drilling tip for easy installation in composite and softwood timber
- Satin finish to compliment your Satin hinge
-
- M5 metric thread size x 10mm length
- 316 Marine Grade Stainless Steel
- Pack of 6
- Thread pitch: 0.8mm
-
- Zenith trusted quality at competitive prices
- Countersunk head for flush finish
- Pre-drill pilot hole for both shank and thread
-
- Chamfered ends
- Imperial sizing
- Zinc plated suitable for internal use and areas not subject to direct weather
-
- M6 metric thread size x 45mm length
- Socket head
- Matte black
- Pack of 4
- Thread pitch: 1mm
-
- Contains a built in washer that is serrated to resist loosening
- Galvanised steel for additional protection against outside elements, limiting corrosion
- Convenient pack of 10
-
- Countersunk head for flush finish in hinges
- Self-drilling tip for easy installation in composite and softwood timber
- Matt black finish to compliment your black hinge
- Chemshield technology for excellent corrosion protection
-
- Fast & easy to install
- Self-drilling anchors, no pre-drilling required
- All you need is a screwdriver
- Strong holding power
-
- Outstanding resistance to corrosion - suitable for highly corrosive areas, specifically along the coastline
- Countersunk head
- Suitable for external use
- Nuts included
-
- Nylon is lightweight, tough, resistant to corrosion and has good electrical insulating properties
- Conforms easily to irregular surfaces and provide limited vibration dampening
- Suitable for imperial and metric
- For external use
-
- Internal star washers
- The internal tabs run along the inside diameter providing superior locking capabilities
- Ideal for applications that require continuous reliability
- Zinc plated for internal applications
- Assortment pack of M14, M15, M16
