Ramset
Sort Most relevant
Showing 36 of 344 results
-
- Patented "pull-down" expansion sleeve closes gaps of up to 5mm providing enhanced security.
- Fully assembled "through fixture" anchor eliminates marking out and re-positioning of fixtures.
- Easy to use
-
- Use for 10G Tapcon AnkaScrews
- Use with hammer action drill only
- Trusted Ramset quality
-
- Ramset™ wall plugs are tapered at one end for quick and easy insertion
- Suitable for 4-6 gauge screws.
- Ramset™ wall plugs are available in a neat and convenient frame pack.
-
- Ramset™ wall plugs are tapered at one end for quick and easy insertion
- Suitable for 4-6 gauge screws.
- Ramset™ wall plugs are available in a neat and convenient frame pack.
-
- Use for 14G Tapcon AnkaScrews
- Use with hammer action drill only
- Trusted Ramset quality
-
- Suitable for cleaning holes 8mm to 12mm in diameter up to 280mm deep
- Clean dust and debris from holes
- Easy to use
-
- Anti-rotation barbs prevent the anchor from rotating in the hole.
- Built in collar prevents loss off anchor in over drilled holes.
- Nylon sleeve reduces the effects of cold bridging. e.g. mould growth, when compared to all-metal anchors.
- Suitable for use with 5 - 7 gauge screws.
-
- Quick and easy to install and remove.
- Can be hammered all the way into the hole without pre-expansion.
- The drive screw’s saw tooth thread makes it easy to drive and unscrew.
- A wide, flat collar with collapsible sleeve design, ensures tight fixing.
- Nylon body provides insulation between drive screw and work surface.
-
- Anti-rotation barbs prevent the anchor from rotating in the hole.
- Nylon sleeve reduces the effects of cold bridging. e.g. mould growth, when compared to all-metal anchors.
- Suitable for use with 6 - 9 gauge screws.
-
- Patented "pull-down" expansion sleeve closes gaps of up to 5mm providing enhanced security
- Fully assembled "through fixture" anchor eliminates marking out and re-positioning of fixtures
- Easy to use
-
- Anti-rotation barbs prevent the anchor from rotating in the hole.
- Nylon sleeve reduces the effects of cold bridging. e.g. mould growth, when compared to all-metal anchors.
- Suitable for use with 10 - 14 gauge screws.
-
- Ramset™ wall plugs are tapered at one end for quick and easy insertion
- Suitable for 14-16 gauge screws.
- Ramset™ wall plugs are available in a neat and convenient frame pack.
-
- Wide wingspan for maximum holding power.
- Anti-rotation fins prevent spinning in the hole when installing the screw.
- Low-profile head allows for flush fixing.
- Nylon body is non-conductive.
-
- Wide wingspan for maximum holding power.
- Anti-rotation fins prevent spinning in the hole when installing the screw.
- Low-profile head allows for flush fixing.
- Nylon body is non-conductive.
-
- Quick and easy to install and remove.
- Can be hammered all the way into the hole without pre-expansion.
- The drive screw’s saw tooth thread makes it easy to drive and unscrew.
- A wide, flat collar with collapsible sleeve design, ensures tight fixing.
- Nylon body provides insulation between drive screw and work surface.
-
- Anti-rotation barbsto prevent the anchor from rotating in the hole
- Countersunk sleeve allows for flush finishing
- Nylon sleeve reduces the effects of cold bridging i.e mould growth, when compared to all-metal anchors
- Suitable for use with 10 - 14 gauge screws
-
- Patented "pull-down" expansion sleeve closes gaps of up to 5mm providing enhanced security.
- Fully assembled "through fixture" anchor eliminates marking out and re-positioning of fixtures.
- Easy to use
-
- Suitable for cleaning holes 16mm to 20mm in diameter up to 300mm deep
- Cleaning dust and debris from holes
- Easy to use
-
- Close to edge fixing
- Superior clamping force
- Easy to install and remove
-
- Anti-rotation barbs prevent the anchor from rotating in the hole
- Countersunk sleeve allows for flush finishing
- Nylon sleeve reduces the effects of cold bridging. e.g. mould growth, when compared to all-metal anchors
- Complete with hex head screw for a easy installation
- Supplied with galvanised screw for increased corrosion protection in external applications
-
- Quick and easy to install and remove
- Can be hammered all the way into the hole without pre-expansion
- The drive screw’s saw tooth thread makes it easy to drive and unscrew
- A wide, flat collar with collapsible sleeve design, ensures tight fixing
- Nylon body provides insulation between drive screw and work surface
-
- Patented "pull-down" expansion sleeve closes gaps of up to 5mm providing enhanced security.
- Fully assembled "through fixture" anchor eliminates marking out and re-positioning of fixtures.
- Countersunk head provides a neat finish, flush with the fixture surface
-
- Patented "pull-down" expansion sleeve closes gaps of up to 5mm providing enhanced security
- Fully assembled "through fixture" anchor eliminates marking out and re-positioning of fixtures
- Countersunk head provides a neat finish, flush with the fixture surface
-
- Spreads adhesive 360 degrees
- Utilised in close to edge applications
- Accommodates 8 and 10mm Ramset Anchor Studs
-
- Close to edge fixing
- Superior clamping force
- Easy to install and remove
-
- Ramset™ wall plugs are tapered at one end for quick and easy insertion
- Suitable for 10-12 gauge screws.
- Ramset™ wall plugs are available in a neat and convenient frame pack.
-
- Anti-rotation barbs prevent the anchor from rotating in the hole
- Built in collar prevents loss off anchor in over drilled holes
- Nylon sleeve reduces the effects of cold bridging i.e mould growth, when compared to all-metal anchors
- Suitable for use with 5 - 7 gauge screws
-
- Anti-rotation barbs prevent the anchor from rotating in the hole
- Nylon sleeve reduces the effects of cold bridging i.e mould growth, when compared to all-metal anchors
- Light duty
- Suitable for use with 6 - 9 gauge screws
-
- Quick and easy to install and remove.
- Can be hammered all the way into the hole without pre-expansion.
- The drive screw’s saw tooth thread makes it easy to drive and unscrew.
- A wide, flat collar with collapsible sleeve design, ensures tight fixing.
- Nylon body provides insulation between drive screw and work surface.
-
- Uses gravity and clamping force to anchor light-weight fittings to plasterboard walls.
- Lack of a protruding flange allows for flush fixing.
- Light duty
-
- Quick and easy to install and remove.
- Can be hammered all the way into the hole without pre-expansion.
- The drive screw’s saw tooth thread makes it easy to drive and unscrew.
- Mushroom head.
- Nylon body provides insulation between drive screw and work surface.
-
- Anti-rotation barbs prevent the anchor from rotating in the hole
- Countersunk sleeve allows for flush finishing
- Nylon sleeve reduces the effects of cold bridging i.e mould growth, when compared to all-metal anchors
- Suitable for use with 14 - 18 gauge screws
-
- Non conductive nylon body.
- Light Duty
- Easy to use
-
- Quick and easy to install and remove
- Can be hammered all the way into the hole without pre-expansion
- The drive screw’s saw tooth thread makes it easy to drive and unscrew
- Countersunk head for a finish flush with the fixture
- Nylon body provides insulation between drive screw and work surface
-
- Patented "pull-down" expansion sleeve closes gaps of up to 5mm providing enhanced security
- Fully assembled "through fixture" anchor eliminates marking out and re-positioning of fixtures
- Countersunk head provides a neat finish, flush with the fixture surface
