General Fasteners
Sort Best selling
Showing 36 of 314 results
-
- Manufactured in Australia
- G300 minimum steel grade
- Z275 minimum corrosion protection
-
- Manufactured in Australia
- G300 Minimum steel grade
- Z275 minimum corrosion protection
-
- Suitable for framing application in accordance with AS1684.2 and AS1684.3
- 316 Stainless Steel – durable, corrosion resistant, and suitable for use in coastal or high corrosion environments
- Versatile bracket – simply bend to your needs!
- Australian Made - High quality, peace of mind, and supporting Aussie jobs
-
- Quick and easy to install
- Made from Galvabond® sheet steel for high resistance to corrosion
- Satisfies the minimum specification of clause 1.15 of AS1684 part 2 and 3, and clause 1.14 of AS1684.4.
-
- Round head
- Stainless steel 304
- Pack of 8
- Includes Torx® driver bit
- Thread pitch: 1mm
-
- Hammer-in method makes installation quick and easy.
- Full expansion of the anchor is evident when the head of the expansion nail sits flush with the flange.
- Once fully set, the ShureDrive™ becomes tamper resistant.
- Large flange prevents pull-out.
-
- Use for many nail fixed timber joints
- Made from Galvabond® sheet steel for high resistance to corrosion
- Satisfies the minimum specification of clause 1.15 of AS1684 part 2 and 3, and clause 1.14 of AS1684.4
-
- Use for many nail fixed timber joints
- Made from Galvabond® sheet steel for high resistance to corrosion
- Satisfies the minimum specification of clause 1.15 of AS1684 part 2 and 3, and clause 1.14 of AS1684.4
-
- Australian made
- Maximises protection of homes against termites
- Manufactured in accordance with AS3660-1993
- Available for concrete or timber stumps
-
- Pryda Multigrips suitable for high load applications such as a tie-down connector for trusses or rafters to top plates for fixing joists to the face of bearers
- Manufactured from G300-Z275 galvanised steel or marine grade stainless steel.
- Trusted Pryda quality
-
- M8 metric thread size x 40mm length
- 316 Marine Grade Stainless Steel
- Pack of 4
- Thread pitch: 1.25mm
-
- For joining timber at right angles
- Roof batten or purlin to a truss or rafter
- Made from Galvabond® sheet steel for high resistance to corrosion
-
- M8 metric thread size x 75mm length
- Made from 316 marine grade stainless steel
- Pack of 2
-
- Great value
- Galvanised
- Reinforced head
-
- For joining timber at right angles
- Made from Galvabond® sheet steel for high resistance to corrosion
- Usage: roof batten or purlin to a truss or rafter; tie-down connectors; carport construction; deck construction; right angle joints; pergola construction
-
- Australian made
- Maximises protection of homes against termites
- Manufactured in accordance with AS3660-1993
- Available for concrete or timber stumps
-
PRYDAPryda Minigrip 57 x 35mm
- Use as a tie-down connector or right angle joint for construction of carports, decks or pergolas
- Made from Galvabond® sheet steel for high resistance to corrosion
- Suitable for lighter load applications
-
- Longer, thicker and stronger than galvanised clouts.
- Tapered head and one-piece construction for greater strength.
- Specifically for fixing of all Pryda bracings and timber connectors.
-
- M8 metric thread size x 35mm length
- Stainless steel 316
- Hex Head
- Pack of 2
- Thread pitch: 1.25mm
-
- Quick and easy to install, removing the need to lift and flip wall frames, helping to prevent lost time injuries during pre-fabrication manufacture
- The Ezi Stud Tie achieves an impressive 5.5kN hold down capacity, 60 per cent more than existing Pryda single sided alternatives
- On site, the Ezi Stud Tie is easy to install with no checking of timber required. The stud tie can be fitted after the ribbon plate (top plate packer) has been attached and is pre-bent to ensure correct placement
-
- Metric thread size M6 x thread length 16mm
- Stainless steel
- Supplied in retailer pack of 10 pieces per card
- Hex head
- Thread pitch: 1mm
-
- Compliant with National Construction Code of Australia
- Self-drilling point for faster installation
- One-handed operation for less fatigue and greater safety
- Coloured head for compliance
- Compatible with impact drivers
-
- Use as a tie-down connector or right angle joint for construction of carports, decks or pergolas
- Made from Galvabond® sheet steel for high resistance to corrosion
- Satisfies the minimum specification of clause 1.15 of AS1684 part 2 and 3, and clause 1.14 of AS1684.4.
-
- A3 steel, zinc-plated class 8.8 for superior high quality
- Sturdy storage case with separate compartments
- Removable plastic separate inserts offers multiple combination for the parts storage inside the case
-
- Designed and tested to conform to Australia's stringent Brick Tie Code AS2699
- Australian made.
- Light Duty: To suit 50mm cavity between brickwork and timber or steel frame.
- R Rating R2
- Supplied with 3.2 x 40mm wood weld nails.
-
- Compliant with National Construction Code of Australia
- Self-drilling point for faster installation
- One-handed operation for less fatigue and greater safety
- Coloured head for compliance
- Compatible with impact drivers
