Wall & Floor Anchors
Sort Best selling
Showing 36 of 329 results
-
- 6mm Tungsten Carbide Drill Bit
- 10 x 35mm Red Wall Plugs
- 10 x 35mm 6G Screws
-
- High load bearing for hollow cavities and walls
- Ideal for wall installations
- Universal fixing points with hexagonal nuts
- Use with single and double sheet boards; masonry hollow cavities where depth allows
-
- Patented "pull-down" expansion sleeve closes gaps of up to 5mm providing enhanced security
- Fully assembled "through fixture" anchor eliminates marking out and re-positioning of fixtures
- Unique "pull-down" section
-
- 5.8 Grade steel
- Medium to high tensile and shear performance
- Galvanised finish
- Eye bolt head for added anchoring point
-
- Patented "pull-down" expansion sleeve closes gaps of up to 5mm providing enhanced security.
- Fully assembled "through fixture" anchor eliminates marking out and re-positioning of fixtures.
- Unique "pull-down" section
-
- Wide wingspan for maximum holding power
- Anti-rotation fins prevent spinning in the hole when installing the screw
- Low-profile head allows for flush fixing
- Nylon body is non-conductive
-
- Patented WERCS thread reduces jamming making installation easier
- New thread pitch increases clamping force for greater security
- Lower thread height at the tip makes starting easier
- 100% removable
- Ideal for close-to-edge or close-to-anchor installation
-
- 8mm Tungsten Carbide Drill Bit
- 10 x 50mm Blue Wall Plugs
- 10 x 50mm 10G Screws
-
- Anti-rotation barbs prevent the anchor from rotating in the hole
- Nylon sleeve reduces the effects of cold bridging i.e mould growth, when compared to all-metal anchors
- Suitable for use with 14 - 18 gauge screws
-
- Patented "pull-down" expansion sleeve closes gaps of up to 5mm providing enhanced security.
- Fully assembled "through fixture" anchor eliminates marking out and re-positioning of fixtures.
- Unique "pull-down" section
-
- Holds up to 50kg on 10mm plasterboard
- Fit in under 20 seconds
- Reusable and recyclable
- Ideal for: AV equipment, light fittings, cabinets and bathroom suites.
-
- Close to edge fixing
- Superior clamping force
- Easy to install and remove
-
- Wide wingspan gives high loadings in both plasterboard wall and ceiling applications.
- Lack of a protruding flange allows for flush fixing.
- metal wing cavity
-
- Easy to install
- Superior holding power
- 2 expandable wings that grip tight behind drywall
- 2 lateral wings hold the anchor in place, preventing any rotation while the screw is inserted
-
- Patented "pull-down" expansion sleeve closes gaps of up to 5mm providing enhanced security
- Fully assembled "through fixture" anchor eliminates marking out and re-positioning of fixtures
- Hex Bolt provides a low profile finish without a protruding thread
-
- 5.8 Grade Steel
- Galvanised finish
- Eye Bolt Head for convenient anchoring point
-
- Patented WERCS thread reduces jamming making installation easier
- New thread pitch increases clamping force for greater security
- Lower thread height at the tip makes starting easier
- 100% removable
- Ideal for close-to-edge or close-to-anchor installation
-
- Medium to high tension capacity
- Medium to high shear capacity
- Simple installation
-
- Medium to high tension capacity
- Medium to high shear load capacity
- Simple installation
- Manufactured from 5.8 grade steel
- 40Mu galvanised finish
-
- Medium to high tension capacity
- Medium to high shear load capacity
- Simple installation
-
- Medium to high tension capacity
- Medium to high shear load capacity
- Simple installation
- Manufactured from 5.8 grade steel
- 40Mu galvanised finish
-
- Suitable for walls 10 to 16mm thick
- Combination Head for easy installation
- Yellow Zinc Plated
- Suitable for Plasterboard, Masonite & Plywood
- Holds up to 10kg
-
- Easy Clip On or Hammer Installation
- Tensioned / Spring loaded Metal Clip
- Suitable for 16 - 20mm wiring / cabling
-
- Galvanised finish
- T40 Torx Drive
- Quick and easy installation
- A removable fastener
-
- Medium to high tension capacity
- Medium to high shear load capacity
- Simple installation
-
- Medium to high tension capacity
- Medium to high shear load capacity
- Simple installation
-
- Holds up to 60kg on 10mm plasterboard
- Fit in under 20 seconds
- Reusable and recyclable
- Ideal for: wall-mounted TVs, heaters, AC units and kitchen cupboards.
-
- Patented "pull-down" expansion sleeve closes gaps of up to 5mm providing enhanced security.
- Fully assembled "through fixture" anchor eliminates marking out and re-positioning of fixtures.
- Unique "pull-down" section
-
- Suitable for blowing dust from drilled holes.
- cleaning dust and debris from holes
- Easy to use
-
- Quick and easy to install and remove
- Can be hammered all the way into the hole without pre-expansion
- The drive screw’s saw tooth thread makes it easy to drive and unscrew
- A wide, flat collar with collapsible sleeve design, ensures tight fixing
- Nylon body provides insulation between drive screw and work surface
-
- Close to edge fixing
- Superior clamping force
- Easy to install and remove
-
- Anti-rotation barbs prevent the anchor from rotating in the hole
- Nylon sleeve reduces the effects of cold bridging. e.g. mould growth, when compared to all-metal anchors
- Light duty nylon anchor
-
- Easy to install
- Superior holding power
- 2 expandable wings that grip tight behind drywall
- 2 lateral wings hold the anchor in place, preventing any rotation while the screw is inserted
-
- Tapered at one end for quick and easy insertion.
- Economical roll.
- Suitable for 10 - 12 gauge screws.
-
- Close to edge fixing
- Superior clamping force
- Easy to install and remove
-
- Patented "pull-down" expansion sleeve closes gaps of up to 5mm providing enhanced security.
- Fully assembled "through fixture" anchor eliminates marking out and re-positioning of fixtures.
- Unique "pull-down" section
